Power Electronics trainer
Power electronic trainers are the basic necessity of every power electronic lab these trainers provide sufficient knowledge of the behavior and characteristics of power-semi-conductor devices such as SCR, TRIAC, etc. Power electronic trainers are being widely used in various engineering universities
2025-06-28 16:34:32 - Adil Khan
Power Electronics trainer
Project Area of Specialization 3D/4D PrintingProject SummaryPower electronic trainers are the basic necessity of every power electronic lab these trainers provide sufficient knowledge of the behavior and characteristics of power-semi-conductor devices such as SCR, TRIAC, etc. Power electronic trainers are being widely used in various engineering universities of Pakistan however the problem is that these trainers are imported from foreign countries at a high price point. This project seeks to manufacture the same modules at an affordable price point.
Project Objectives- Manufacture 4 Modules of a Power Electronics Trainer
- Cost Reduction.
- To Make a Variable Frequency Drive by inter connecting all the modules.
- Module Selection
- Identification of the Components
- Tracing of the Circuit
- Troubleshooting on vero board
- PCB Printing
- Components Soldering
These Steps were followed for all the modules.
Benefits of the Project- Cost Effective
- Easy After Sales Service
- Beneficial for Educational Purposes
- Behavioral Analysis of several Power Electronic Devices
- SCR/TRIAC Module
- Reference Variable Generator
- IGBT Drive Set
- Single Phase PWM Controller
All these Modules Combine to form a Variable Frequency Drive and they will be presented in a form of trainer.
Final Deliverable of the Project Hardware SystemType of Industry Education Technologies OthersSustainable Development Goals Industry, Innovation and InfrastructureRequired Resources| Item Name | Type | No. of Units | Per Unit Cost (in Rs) | Total (in Rs) |
|---|---|---|---|---|
| Total in (Rs) | 75586 | |||
| SCR | Equipment | 1 | 30 | 30 |
| TRIAC | Equipment | 1 | 25 | 25 |
| Inductor | Equipment | 1 | 25 | 25 |
| Copper Clad Board | Equipment | 1 | 200 | 200 |
| Ferric Chloride | Equipment | 1 | 70 | 70 |
| Drill | Equipment | 1 | 600 | 600 |
| Two Way Switch | Equipment | 4 | 25 | 100 |
| Resistors | Equipment | 6 | 2 | 12 |
| CT60-AM | Equipment | 4 | 600 | 2400 |
| IR2130-DIP | Equipment | 2 | 800 | 1600 |
| Vero Board | Equipment | 1 | 70 | 70 |
| IC Base (28 pin) | Equipment | 1 | 10 | 10 |
| IC base (14 Pin) | Equipment | 3 | 3 | 9 |
| Diode (1N4007) | Equipment | 6 | 1 | 6 |
| Crystal LED | Equipment | 3 | 2 | 6 |
| Resistor | Equipment | 37 | 1 | 37 |
| Capacitor | Equipment | 12 | 8 | 96 |
| Potentiometer | Equipment | 3 | 20 | 60 |
| Jumper | Equipment | 7 | 10 | 70 |
| 40 Pin IC Base | Equipment | 1 | 10 | 10 |
| Voltage Regulator | Equipment | 1 | 15 | 15 |
| 7107 | Equipment | 1 | 150 | 150 |
| 7805 | Equipment | 1 | 15 | 15 |
| TL431 | Equipment | 1 | 15 | 15 |
| LM324 | Equipment | 2 | 15 | 30 |
| Resistor Sheet | Equipment | 1 | 50 | 50 |
| Capacitor Sheet | Equipment | 1 | 100 | 100 |
| CT60AM | Equipment | 2 | 600 | 1200 |
| IR2130 | Equipment | 2 | 800 | 1600 |
| 74HC244N | Equipment | 1 | 45 | 45 |
| 74LS14 | Equipment | 2 | 35 | 70 |
| 6N137 | Equipment | 4 | 40 | 160 |
| LM7805 | Equipment | 1 | 15 | 15 |
| Soldering Wire | Equipment | 1 | 225 | 225 |
| 4148 | Equipment | 12 | 3 | 36 |
| 4007 | Equipment | 12 | 2 | 24 |
| Interim Report Printing | Miscellaneous | 1 | 500 | 500 |
| Final Report Printing | Miscellaneous | 1 | 1500 | 1500 |
| Data Sheet Printing | Miscellaneous | 15 | 100 | 1500 |
| PCB Printing | Equipment | 4 | 10000 | 40000 |
| Melamite Sheet | Equipment | 2 | 4500 | 9000 |
| Aluminium Frame | Equipment | 1 | 7900 | 7900 |
| Boxes | Miscellaneous | 4 | 1000 | 4000 |
| Screen Printing | Miscellaneous | 4 | 500 | 2000 |