Adil Khan 1 year ago
AdiKhanOfficial #FYP Ideas

IOT based controlling of distributing panel to Maintain Power Factor in Industry

IOT based distribution panel is the type of panel which used for to distributing the input source to different output load while operating with smart techniques. For this purpose we will be using an android app to  perform the various task  like controlling and operating  function and

Project Title

IOT based controlling of distributing panel to Maintain Power Factor in Industry

Project Area of Specialization

Internet of Things

Project Summary

IOT based distribution panel is the type of panel which used for to distributing the input source to different output load while operating with smart techniques. For this purpose we will be using an android app to  perform the various task  like controlling and operating  function and  also showing the current, voltage, power factor to user on mobile screen. It is also showing the above factors on the LCD for the user. It’s improving the load power factor. Raspberry Pi Programming it can interface analogue quantities i.e. current and voltage Power factor improvement and load management.

Project Objectives

  • To design an autonomous distribution Panel Switch on/off appliances smartly, Utility bill can be managed in bounded limits, Make monitoring of all appliances in industries or commercial 

  • Be able to understand the designing of different Distribution panel  i.e. wire selection, breakers, load distribution
  • Maintaining of power factor
  • Be able to establish a Wi-Fi based communication
  • Be able to provide a community service by which every user may see how power is being distributed with in commercial or industries and see the consumption of units

Project Implementation Method

  • Our project is contain a hadware and software combination keeping this factor in mind we have to impliment  our project according to the following methodolgy. 
  • The 3-phase source will enter to a main breaker
  • Then the DC source will be enable for the on condition of the Raspberry Pi.
  • Then it will be read or take the information from the Current Transformers & Potential Transformers  and will be provide the platform for the user to make its decision .
  • Thus the command will be given through a mobile app to perform a particular task.

Benefits of the Project

  • The panel should  fulfil the user requirements. It will be helpful for the Industrial purpose.
  • User can be able to observe the different parameters from anywhere because of smart system ability.
  • It is use for power factor improvement in industry
  • It is easily operated due to IOT based   
  • It will be available at suitable price from open market.

Technical Details of Final Deliverable

The Raspberry Pi 3 Model B+ 

  • Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz.
  • 1GB LPDDR2 SDRAM.
  • 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE.
  • Gigabit Ethernet over USB 2.0 (maximum throughput 300 Mbps)
  • Extended 40-pin GPIO header.

ESP- 8266

  • Processor: L106 32-bit RISC microprocessor core based on the Tensilica Xtensa Diamond Standard 106Micro running at 80 MHz.
  • Memory:
  • External QSPI flash: up to 16 MiB is supported (512 KiB to 4 MiB typically included)
  • IEEE 802.11 b/g/n Wi-Fi. ...
  • 16 GPIO pins.
  • SPI.
  • I²C (software implementation)

Current Transformer (CT)  

Class of Accuracy

0.5

Rated Burden

5.00 VA

Power Frequency Withstand Voltage

 3KV

Highest System Voltage

433 V

Nominal System Voltage

400 V

Frequency

50 Hz

Supply System

3 Ph. Solidly grounded Neutral System

3-Phase inductive motor with the following data

1

Rated power

2 hp

2

Rated frequency

60 Hz

3

Rated Input Voltage

220 V

4

Rated Speed

1164 RPM

5

Number of poles

6

6

Stator Resistance

0.294 ohm

7

Stator leakage Inductance

1.39 mH

8

Rotor Resistance

0.156 ohm

9

Rotor Leakage inductance

0.74 mH

10

Magnetizing inductance

41.0mH

11

Moment  of Inertia  / Motor & Load

0.8 kgm^2

12

1 hp = 746 watt

Capacitor Bank

Power Factor Control

The PFC relay/equipment shall have a range suitable for proper selection of switching In/Out of the Sub-banks to maintain the Target Power Factor via the PLC. The relay PF setting range shall be.

0.8 CAPACITIVE – UNITY –0.8 INDUCTIVE

The relay shall have as a minimum a digital display of PF, Target PF, Operation Time Delay, voltage and current.

Class of Accuracy

Rated Burden

Power Frequency Withstand Voltage

Highest System Voltage

Nominal System Voltage

Frequency

Supply System

1

2

3

4

5

6

7

8

9

10

11

12

Final Deliverable of the Project

HW/SW integrated system

Type of Industry

Energy

Technologies

Internet of Things (IoT)

Sustainable Development Goals

Industry, Innovation and Infrastructure

Required Resources

1

Rated power

2 hp

2

Rated frequency

60 Hz

3

Rated Input Voltage

220 V

4

Rated Speed

1164 RPM

5

Number of poles

6

6

Stator Resistance

0.294 ohm

7

Stator leakage Inductance

1.39 mH

8

Rotor Resistance

0.156 ohm

9

Rotor Leakage inductance

0.74 mH

10

Magnetizing inductance

41.0mH

11

Moment  of Inertia  / Motor & Load

0.8 kgm^2

12

1 hp = 746 watt

If you need this project, please contact me on contact@adikhanofficial.com
0
192
Design and Fabrication of Energy Efficient Water purifier

Water is obtained mainly from two sources underground water (Boring water, well water) and...

1675638330.png
Adil Khan
1 year ago
Design of nanofibrous membrane for biobased face mask to limit the Cov...

The emergence of coronavirus and its rapid spread across the globe has led to a large pand...

1675638330.png
Adil Khan
1 year ago
Design and Development of Brushless Motor Thrust Stand

Brushless motors have replaced brushed motors in almost every field because of their so ma...

1675638330.png
Adil Khan
1 year ago
Prototyping of Electrical Systems of an Electric Vehicle(EV)

Fossil fuels are essential and primary source of energy. The global consumption of fossil...

1675638330.png
Adil Khan
1 year ago
Implementation of Object detection and Avoidance Algorithm on FPGA A s...

Implementation of object Detection/ Avoidance Algorithm on FPGA(NI MyRIO) for step towards...

1675638330.png
Adil Khan
1 year ago