Adil Khan 1 year ago
AdiKhanOfficial #FYP Ideas

Wireless power transmission through Rectenna and its utilization.

In this Project we introduce another idea for WPT, through Microwave Power transmission (MPT). In order to reduce the transmission losses, for this process we used a special type of Antenna which named as Rectenna. Rectenna convert Microwave power into DC power which we utilize. Wireless pow

Project Title

Wireless power transmission through Rectenna and its utilization.

Project Area of Specialization

Wearables and Implantable

Project Summary

In this Project we introduce another idea for WPT, through Microwave Power transmission (MPT). In order to reduce the transmission losses, for this process we used a special type of Antenna which named as Rectenna. Rectenna convert Microwave power into DC power which we utilize.

Wireless power Transmission (WPT) is the process of transfer power from one end to another end or from source to the loud without wires. The WPT is also called wircity. The WPT we utilized to charge the Mobile Phone and low power rating device such as Digital camera and Laptop etc.

Project Objectives

  1. Eliminate the cord on the ground that make trapping hazards.
  2. A necessary step toward consumer wireless power transfer.
  3. Allow no wire installation.
  1. Used to charge Mobile-Phone, Laptop.
  2. It is also used to charge the digital camera.

Project Implementation Method

Methodology of WPT Trough Rectenna:

The research methodology of The WPT we divided into two Parts.

Transmitter:

                 Transmitter Block Diagram.

  • Ads software used for simulation of Rectenna.
  • 2.4GHz frequency-Band.
  • Transmitting Antenna.

Receiver:

In Receiving-side the WPT (RF-signal) is obtained on the Receiving Antenna. By convert the RF received power in to The DC power of about 5V DC. We use the Shottky-Diode for the rectifier purpose.

After rectification we pass the DC voltage through Loss-Pass filter we which remove the High frequency components from the rectifier voltage. Then we connect the DV output to the loud. In the loud we use Mobile Phone charger, for charging of Mobile phone.

The Hardware required For WPT:

  • Rectenna
  • Rectifier(diode)
  • Matching Circuit(Resister , Capacitor and inductor)
  • Low-Pass filter (LPS).

Benefits of the Project

binifits of the project are explained in Objective column.

Technical Details of Final Deliverable

technical detail are explained in methodology.

Final Deliverable of the Project

HW/SW integrated system

Type of Industry

IT

Technologies

Wearables and Implantables

Sustainable Development Goals

Industry, Innovation and Infrastructure

Required Resources

Item Name Type No. of Units Per Unit Cost (in Rs) Total (in Rs)
substrate Equipment21000020000
shortky diode Equipment16801280
inductors Equipment1020200
capacitor Equipment1020200
sma connector Equipment12120014400
chemicals Equipment106006000
resistors Equipment1020200
stand Equipment44001600
Total in (Rs) 43880
If you need this project, please contact me on contact@adikhanofficial.com
0
219
EMG based Pattern Recognition Using Pattern Recognition Technique

This Project will be Use to identify the Human Gender via EMG signals. The EMG signals Wil...

1675638330.png
Adil Khan
1 year ago
AI Mirror

An IOT based project in which different APIs & tools will be merged together to create...

1675638330.png
Adil Khan
1 year ago
Air water generator

Project Definition Looking into one of the most prominent concern in the developing and un...

1675638330.png
Adil Khan
1 year ago
Image Captioning

It is a very challenging task to automatically describe image contents using human-readabl...

1675638330.png
Adil Khan
1 year ago
Vaccine carrier cooling box

We designed an Vaccine Carrier Box having a box . Our aim was to reduce the minimum temper...

1675638330.png
Adil Khan
1 year ago