Self Sufficient Hybrid Powered Smart Irrigation System
This project has majorly two sections. First section comprises of power generation by solar and hydro in order to make project self-sufficient. Second section comprises of control and watering system in order to manage water storage and water flow towards plants. The work flow of this system
Project Title
Self Sufficient Hybrid Powered Smart Irrigation System
Project Area of Specialization
Project Summary
This project has majorly two sections. First section comprises of power generation by solar and hydro in order to make project self-sufficient. Second section comprises of control and watering system in order to manage water storage and water flow towards plants.
The work flow of this system may be best understood by following flow instructions.
- Soil-moisture sensor senses the necessity of water and generate signals when water is needed.
- Controller check sensor’s signal and water storage level.
- Upon receiving signal from sensor, water is supplied to the plant by actuating particular actuator.
- Control system also check the electric power required to run the whole system. It observes the stored electricity as well as load consumption.
- Normally electrical power is generated through solar power (during day time).
- Additional electrical power is generated by hydro by utilizing water flow.
Project Objectives
- Efficient water supply management to deal with water crisis.
- To make self-powered system to deal with power crisis.
Project Implementation Method
- Design and development of smart irrigation system.
- In the first phase, irrigation system will be made. It will comprises of several plants. Moister level of the plants will be sensed and water will be supplied accordingly.
- Design and development of Hybrid Converter. (Solar + Hydro)
- After the completion of irrigation system, the required power consumption will be measured. Second phase will comprises of designing and development of a power supply capable of handling at least twice of the required power consumption. This power supply will be made by using solar energy and hydro energy. For this, a hybrid converter will be designed and developed.
- Fabrication of mechanical structure.
- In the last phase, the required mechanical structure will be fabricated.
Benefits of the Project
Saving water
Saving electricity
Cost effective
Saving time on forming
More earn through irrigation
Technical Details of Final Deliverable
The technical details of Final Deliverable are as under.
Raspberry pi. Raspberry Pi 3 Model B was released in February 2016.in this project role of raspberry pi work is smartly control whole project .CPU,1.4 GHz 64/32-bit quad-core ARM Corte.Operating system linux And raspbian Power: 1.5 W (average when idle) to 6.7 W
Power supply. Input Frequency Range: 50 – 60Hz,Output Regulation. 5.7V to 12V Output Load Range: 0 – 3A
Operating/Storage Temperature, 0ºC ~+40ºC/ -20ºC~+70ºC,Operating/Storage Humidity: 20%~80%RH/10%~90%RH,Protection,Over Voltage/Short Circuit.
Dual-Input Converter. in this project we are intigrate dual-input converter new topology for dual energy source conversion is presented. The topology is capable of interfacing sources of different voltage-current characteristics to a common load, while achieving a low part count. A fixed frequency switching strategy is investigated and the resulting operating modes are analyzed.
Final Deliverable of the Project
Type of Industry
Technologies
Sustainable Development Goals
Required Resources
| Item Name | Type | No. of Units | Per Unit Cost (in Rs) | Total (in Rs) |
|---|---|---|---|---|
| Raspberry pi B+ | Equipment | 1 | 6000 | 6000 |
| Sd Card 32Gb | Equipment | 1 | 1100 | 1100 |
| Arduino (Rv3) | Equipment | 1 | 600 | 600 |
| Soil Moisture LM393 | Equipment | 4 | 250 | 1000 |
| Centrifugal pump | Equipment | 1 | 1500 | 1500 |
| pen-stock line | Equipment | 5 | 200 | 1000 |
| Drip-Irrigation Fitting | Equipment | 6 | 180 | 1080 |
| Water Tank(5 Liter) | Equipment | 2 | 550 | 1100 |
| 2-way Restricted-Flow Water Shut-Off | Equipment | 3 | 200 | 600 |
| Power supply(12V And 6V) | Equipment | 1 | 4000 | 4000 |
| Boost Converter | Equipment | 1 | 3500 | 3500 |
| Dual-Input converter | Equipment | 1 | 6000 | 6000 |
| GSM-Module | Equipment | 1 | 1800 | 1800 |
| HDT-11 | Equipment | 1 | 150 | 150 |
| Display(16*2) | Equipment | 1 | 200 | 200 |
| Micro Hydro-Turbine | Equipment | 1 | 12000 | 12000 |
| Battery(30A) | Equipment | 1 | 3500 | 3500 |
| Mono Crystalline Black - 150 Watt Solar Panel | Equipment | 2 | 7500 | 15000 |
| Project Mechanical Structure | Equipment | 1 | 8000 | 8000 |
| Solenoid Pump | Equipment | 2 | 675 | 1350 |
| wires And Soldering Wire Circuits printing | Miscellaneous | 1 | 8000 | 8000 |
| Total in (Rs) | 77480 |
If you need this project, please contact me on contact@adikhanofficial.com
Online Pizza ordering System like that Fast food Restaurant Management...
There are three modules of this system/application for food app system/application that is...
Wearable Soft Robot for Upper limb Assistance and Rehabilitation
Hand injuries for example fractures etc. can cause the muscles to weaken which results in...
Real Time Emotion Charting Device Using Physiological Signals
The project is an Emotion Charting Device Using ECG and GSR Signals classifying into 7 emo...
Design and development of helmet testing rig for impact loading
According to WHO (World health organization), around 4000 fatalities occur in pakista...