Adil Khan 1 year ago
AdiKhanOfficial #FYP Ideas

Performance comparison of Linear Oscillating Actuators with Rare-Earth and Ferrite magnets

Linear Actuators are electromechanical devices which provide bidirectional motion in a single axis for a specific load without any screws, gears, or crankshafts. They are characterized by the absence of mechanical energy conversion system, which results in fast response, high dynamic performance, an

Project Title

Performance comparison of Linear Oscillating Actuators with Rare-Earth and Ferrite magnets

Project Area of Specialization

Electrical/Electronic Engineering

Project Summary

Linear Actuators are electromechanical devices which provide bidirectional motion in a single axis for a specific load without any screws, gears, or crankshafts. They are characterized by the absence of mechanical energy conversion system, which results in fast response, high dynamic performance, and high reliability. Meanwhile due no end windings and high permanent magnet (PM) utilization, tubular linear actuators have the advantages of high air-gap flux density and high efficiency compared to flat linear actuators

Linear Oscillating Actuator (LOA) consist of two main parts, called stator and mover. The stator, actuator’s stationary part, generates a controlled electromagnetic energy. This energy is transformed into mechanical work by displacing the armature (moving part) to the position where the magnetic flux faces the least reluctance. On the basis of moving part (mover) configuration there are three types of LOA which are moving iron, moving coil and moving magnet. The applications of the proposed LOA are automation, circuit breakers, biomedical aerospace industries and compressor for refrigerator system

The main purpose of this project is to investigate the performance of moving magnet LOA using Ferrite and rare earth magnet with tubular structure and then their performance for compressor application

Project Objectives

The whole world is facing energy crisis in the power sector. Due to high value and lack of availability of energy, currently the attention of saving energy is prominent. Saving energy of household instrument especially refrigerator which consumes 20 to 40 percent of electrical energy in a house. In refrigerator, the large amount of energy is consumed in compressor. A compressor of high efficiency can save large amount of energy. Using LOA in compressor of refrigerator can utilize energy in efficient manner and it is very cost effective and has better outputs as compared to rotatory mechanism.

The main Objectives of this project are:

  • To design and analyzed moving magnet LOA (using rare earth and ferrite magnets) with high efficiency and power density and then compared their performance]
  • To fabricate both moving magnets LOA and analyze their outputs.
  • To validate the simulation results of both LOA experimentally, compared and finally proposed the best one for compressor application.

Project Implementation Method

The project implementation is divided it into three parts given below.                                                      

  • COMSOL Simulation  
  • Fabrication
  • Experimental result and Comparison

COMSOL Multiphysics is the software package used to design and evaluate the performance of the proposed actuator. To evaluate the electromagnetic field of the actuator ,2D-axisymmetric FEM solver is used. Generally, COMSOL Multiphysics software is a multipurpose software, in which the magnetic field module is used for the designing and analyzing of the LOA. Starting from the designing process and setting conditions for the purposed model are elaborated. Different parameters settings, materials used, coil and different setting conditions are explained. The performance of the proposed actuator is analyzed using parametric sweep on that parameter and select the optimum value under constrained region. And similarly, the output response is examined using g parametric sweep on the input loading parameters.

After completion of COMSOL designing the process od fabrication will start. Lathe machine is used during fabrication, to manufacture all the required parts of the proposed model of LOA (for both the magnets). In the fabrication process the most important thing is that the dimensions of all required fabricated parts must be same as in COMSOL designing. The stator and mover are made of low carbon steel and wire used is made of copper of 18 gauge in AWGS. Coil is made using winding machine and to keep the dimensions of the coil accurate, Vernier caliper is used. Dimensions of the coil must be accurate to keep the coil stress-free in the housing in stator core. The tube of mover core has embedded PM on both sides.

At last, when both the simulation and fabrication completed. The final step is to analyze the experimental results for both magnets using different tests. And when all the results analyzed then the process of comparison will start, and the output results of both magnets will compare for the use of compressor applications. 

Benefits of the Project

This project is beneficial for the refrigerator industry like Haier, Dawlance etc. but especially it would be helpful for the local industries which cannot afford the expenses of other types of expensive actuators. The structure is very simple and have less friction points. Due to the less frictional points there will be less losses. This is also environmental friendly because the noise effect is almost negligible. This is also cost effective because lesser mechanical parts are used, and the main advantage of this project is efficient use of energy. And after this project the manufacturers will be able to design the compressor with higher efficiency in low cost.

Technical Details of Final Deliverable

Mostly in many projects Halbach array configuration is used. The cost of ring-shaped magnets is high and in manufacturing difficulties occurred. Ring shaped permanent magnets have low mechanical strength.

To solve the above problems, the magnets used in this project are axially magnetized. The thrust force of proposed LOA is high, and LOA have low cost, easy to build and overall volume is small as compared to recently designed linear oscillating actuators. In proposed project axially magnetized ring-shaped magnets are used instead of using axially magnetized disk-shaped magnets because they have high mass of the mover.

This project has tubular topology with moving magnets mechanism. This moving magnet type actuator is having a low mover mass, its dynamic response is fast and have a value of high thrust force density and compared with other types of actuators like (moving iron or moving coil type) and it has better efficiency.

The thrust force obtained from the rare earth magnets is high as compare to ferrite magnets but on the other hand ferrite magnet is cost effective. So, for the use of compressor applications ferrite magnet is best for use because we can easily obtain the required thrust force in cheap cost by using ferrite rather than using of rare earth magnets

Final Deliverable of the Project

Hardware System

Core Industry

Manufacturing

Other Industries

Core Technology

Shared Economy

Other Technologies

Sustainable Development Goals

Decent Work and Economic Growth, Industry, Innovation and Infrastructure

Required Resources

Item Name Type No. of Units Per Unit Cost (in Rs) Total (in Rs)
Aluminum Equipment180008000
Low carbon steel Equipment130003000
nuts and bolts Equipment115001500
Load cell (S shaped) Equipment180008000
load cell display Equipment190009000
variable power supply Equipment11900019000
copper wire Equipment160006000
springs Equipment42501000
work banch Equipment170007000
Aurdino Equipment110001000
Magnets Equipment610666396
Mechanic charges Miscellaneous 155005500
Transport charges Miscellaneous 140004000
Total in (Rs) 79396
If you need this project, please contact me on contact@adikhanofficial.com
0
189
Assignment No 1 - Basic Ubuntu Commands and their usage

Assignment No 1 - Basic Ubuntu Commands and their usage

1675638330.png
Adil Khan
6 years ago
dielectric constant measurement using SMRR

 The dielectric constant of liquids is essential to find adulteration in food, agricu...

1675638330.png
Adil Khan
1 year ago
Frequency Controlled Refrigeration

Traditional refrigeration devices control the temperature by operating the compressor in b...

1675638330.png
Adil Khan
1 year ago
Home Automation with Power Consumption

Considering the basic needs of daily life where we all want to have full control of our ho...

1675638330.png
Adil Khan
1 year ago
Microcontroller Gesture Controlled Lifeguard Robot

Lifeguard using Gesture Control When a human falls in the sea, a robot will return him to...

1675638330.png
Adil Khan
1 year ago